Mission, KS HVAC & Plumbing Services

Upon arrival I began the AC tune up. First, I ran a static pressure test. The unit has a max static pressure rating of .8 and the system was testing at .78 just under the max. Next, I checked the blower motor running amps which tested a little high but within manufacturer specifications. I also checked the blower motor capacitor which is a size 20mfd and it’s testing at 100%. I moved to the outdoor unit and connected my refrigerant gangues to test the refrigerant charge in the system. Since it’s a little cooler today my pressures looked a little wonky but I was able to verify that the system is within manufacturer specs. My subcooling target was 13 degrees and my subcool temp was spot on at 13 degrees. I also took a temperature split on the AC and it was at a perfect split of 18 degrees. System is running properly at this time. If you have any questions or concerns please feel free to contact us! Your LBA Technician, Tyler Rickard P.S. No payment was due for todays visit, it was cover

Upon arrival I began the AC tune up. First, I ran the static pressure test on the system. This unit is rated for a max static pressure of 1.0 and the system is testing at .46 which is passing. Next, I checked the running amps in the blower motor inside and it was testing within specs. The blower wheel itself was very clean. Next, I went to the outdoor unit. I connected my refrigerant gauges to check the charge. Because it is only 40 degrees outside today when I was testing the system, it didn’t give me proper readings. But I was able to find the systems charge is still within specs. The temperature split on the system was at a perfect 18 degrees. I checked the running amps on the compressor and the outdoor fan motor and both tested within specs. This system is rather new still and it still looks new to me. If you have any questions or concerns please feel free to contact us! Your LBA Technician, Tyler Rickard P.S. No payment was due for todays visit, it was covered with your membershi

Humidifier drain was not supported, now it's supported to the drop

Dispatch for annual maintenance check on furnace and AC. For the maintenance I check static pressure, flame sensor, refrigerant pressures, contractor and the capacitor. Also checked the blower fan amps on the furnace along with the compressor and the condenser fan amps. All components of the system are operating within manufacturer specifications. Thank you for being a member to LBA services.

Mainline Jetting Completed

Jetting service

Sold jetter

N

N

N

N

Arrived at home and spoke with Pat about main drain blockage. We determined that the upstairs tub was slow due to hair and cried to build up and the pipe. I didn’t do any drain clearing or any other work.

Na

Na

Na

Na

Arrived for furnace maintenance today. Checked static pressure and found it is failing. Heat exchanger has some heat stress. Carbon monoxide test was 0 ppm. Our temperature rise is right at the max, not getting enough air into system. Electrical components are running properly at this time. Blower wheel is clean. Inducer motor has a small leak. My field supervisor is out to discuss the best options for repairs. System is running upon departure. Thanks for choosing LBA.

Charged AC. Set up smart AC in home.

Water Heater Repair – Diagnosed and replaced a malfunctioning thermostat, ensuring precise temperature control and consistent hot water delivery.

Water Heater Repair – Flushed a residential water heater to remove years of sediment buildup, restoring efficient heating and extending the unit’s lifespan. I also inspected and replaced a worn anode rod to prevent future corrosion inside the tank.

System Install Installed 90% furnace with 3 ton ac, new aprilaire 210 filter, new drop, moved humidifier, new return run.

Drop off space heaters

Follow up @ 4 today

Arrived for furnace maintenance today. Furnace is 2012. I found what appeared to be holes in the heat exchanger. Called my supervisor out to recheck. Upon a second look there are holes in the heat exchanger. He will be discussing the best options for you. Thanks for choosing LBA.

Arrived for furnace maintenance today. Checked static pressure and found that it is running over the max rating. A field supervisor is out to diagnose further. The flue is leaking into the furnace. So far it has not caused damage to the furnace. I changed furnace filter. The filter only lasts 3 weeks. All electrical components are within specs. Blower wheel is clean and balanced. System is running upon departure. Thanks for choosing LBA.