Basehor, KS HVAC & Plumbing Services

Arrived to remedy a Mitsubishi mini split that is unable to keep up in the heat. Upon inspection of the unit found it running. Measured a temperature split, and found that the unit was only cooling 15 degrees when we demand 20 from it. Turned off the unit and inspected the power head. Found that the blower wheel (fan) for the unit is heavily coated in debris. Turned the unit back on and tested system functions and made sure it is at least operating properly, if not cooling properly. Unit is working as it should. Went outside and verified the outside unit is operating as designed. Determined that the unit is so dirty it is effecting how the unit operates and will not allow it to operate at max capacity. Called homeowner to go over repair solutions. With homeowners approval reached out to the office to schedule the mini split power head cleaning.

Arrived for ac maintenance today. Started at furnace and checked static pressure, temperature splits, drains, filter, blower wheel, blower motor, and running amps. Static pressure was passing. Blower wheel was starting to pick up dust. All other operations are working properly. At the ac unit I checked refrigerant levels, capacitor, contactor, running amps, fan motor, and coil. All operations are working properly here to. The coil was dirty with debris. Offered options for cleaning and did not want to at his time. Thanks for choosing LBA.

Provided wq estimates

Provided wq estimates

Provided wq estimates

Provided wq estimates

Installed new black iron adapter for customer supplied gas flex line for grille Trip in diagnostic

Full system

Sold

Upon arrival I started the tune up. I found the static pressure was failing at .7 when rated for a max of .5. The blower wheel was dirty and over amping. The dirty blower wheel is throwing dirt into the evaporator coil and causing the air to be pass through the coil evenly. The refrigerant charge on the outdoor condenser was showing very low refrigerant levels and it is the older R22 refrigerant that we no longer carry. Field supervisor Scott arrived to check my static readings. He is taking over the call with the homeowner. Have a great holiday and thank you for your service!

AC Repair Service: Upon responding to a service call regarding an AC unit's insufficient cooling performance, I conducted a thorough inspection and cleared obstructed air ducts, meticulously ensuring unrestricted airflow for optimal cooling performance.

8” return and bypass

HVAC Condenser Coil Cleaning: A customer's AC system was not cooling efficiently. Our technicians cleaned the condenser coil and straightened the fins, significantly improving the system's performance. The client's home now enjoys cool and refreshing air, and we emphasized the importance of regular coil maintenance.

Static call

Arrived to do performance maintenance. Set up for combustion analysis and static pressure tests. Reached out to a supervisor to come out and diagnose the high static pressure Monday morning. Verified operation of all mechanical and electronic components in the furnace. Cleaned the flame sensor and tested its performance. Checked blower for cleanliness and to see if there is any play in the bearings. Checked systems heat exchanger to ensure proper venting of flue gas. Performed an electronic gas leak search. Verified operation of the electronic components of the condenser. See estimates for pricing on recommended repairs. Furnace is operational upon departure.

During maintenance customer system passed static had a good cam count. I also cleaned customers flame sensor ports checked burners and also did amp draws everything looks good today

We were out to evaluate the system and found that the wires had been swapped down at the zoning control board. System was kicking the ac on as if it was a heat pump but it has no reversing valve. After switching wires to the proper terminals system is operating properly.

Zoning Board not working properly.

Responded for a call on no heat. When I arrived by test the furnace in heating mode. Flame ignition was not starting due to a pressure hose. Going from one pressure switch to the other that was not seated correctly. It most likely came loose from the vibration of the blower motor. I then replaced one of the square pressure hoses in the inducer motor. It looked as if it had been pinched because it was at an awkward twisted angle. I then cleaned the last two hoses going from the inducer to the collector box and the pressure switch to the gas valve to make sure there are no obstructions. I then tested the heater three times to make sure it started up correctly.

Company removed the failed softener system and install new novo combo unit. Company checked flushed all fixtures and water heater of potential resin media. Thank you for choosing LBA and have a great day.

Upon arrival, customer mentioned how he’s having inconsistent and low water pressure throughout the system. Tested and verified findings. After further diagnostics determined that water softener had failed and is sending out media resin throughout the whole plumbing system causing pressure problems. Recommended replacing and flushing out the system. Customer authorized work and scheduled for Friday morning.

Installed new furnace. Tested and cycled. Unit is operating properly at this time.

Furnace

Arrived to furnace maintenance. Upon arrival I spoke with the customer who showed me the location of the furnace, ac, and corresponding thermostat. I began my maintenance by cleaning safeties and checking the overall condition of the furnace. This included a safety inspection of the systems heat exchanger. Upon doing this I found large holes had formed within the heat exchanger itself making this system unsafe to operate. I showed the customer these holes live and red tagged/shut down the furnace. My supervisor will be here to go over replacement. Furnace off upon departure.

Customer did not have time for me to come inside.