Mission, KS HVAC & Plumbing Services

Installed new Full System Furnace Model FR951V0703A17M4SCA, AC Unit Model FRA13NZ36AJ1NA, Evap Coil Model FTCFZ3617STANMC. New Thermostat. 2 Year Labor Warranty 10 Year Parts Warranty Limited Lifetime Heat Exchanger Warranty

Furnace replacement

Went for a furnace inspection today. Did a static pressure test, it failed. Did a carbon monoxide leak test, was getting a few different readings. The furnace is unsafe to run. Thank you for choosing LBA services!

Sold furnace

Went for a furnace inspection today. Did a static pressure test, it failed. Did a carbon monoxide leak test, there is a leak. After looking at the heat exchanger, I noticed two holes in it. The furnace is disabled due to being unsafe. Thank you for choosing LBA services!

Today the rooftop unit that serves the used car lot office was diagnosed as having a failed control board. The flame sensor was exposed to higher voltage than it was designed for. Due to this it was also replaced. The unit returned to proper function after these components were sourced, picked up and installed. The unit was visually checked and a carbon monoxide test was done. There is no CO inside of the supply ducts and in the occupied space. Factory parts were used in the repairs today. The parts as well as labor will be warrantied for one year from today. Thank you, Jon Tech notes: York, m/n N1E0842316, s/n ZH150N20N2AAA5A, new control board, flame sensor. Tr (118-70), CO 0ppm.

Completed furnace maintenance and inspection. I checked air pressure and temp splits. I tested all components and amp draws. I found no issues today. Furnace is running within manufacture specifications. I cleaned blower wheel and compartment, replaced filter, renewed membership and installed sensors.

W

W

W

W

Went for a furnace inspection today. Did a static pressure test, it passed. Changed filter. Did a carbon monoxide leak test, there is no leak. Combustion analysis test passed. Inducer motor amperage passed. Gas pressure met factory specifications and pressure switch passed. Temperature split from the supply and return duct passed. Blower wheel is clean and blower motor amperage passed. The other furnace won’t turn on. After inspecting the heat exchanger, I noticed severe rust and multiple cracks. The furnace is unsafe to run. Thank you for choosing LBA services!

Happy call. Furnace passed inspection.

Arrived for furnace maintenance today. Checked static pressure and found it was failing. Since we had completed work for it, I called a field supervisor out to see what the issue was. We found that some dampers were lose and had blown shut. We opened all the dampers and tightened them to stay open. Installed new filter and retested. Static is back down now. Carbon monoxide test was 0ppm. Heat exchanger is good. All electrical components are running properly at this time. System is running upon departure. Thanks for choosing LBA.

Sale

Arrived for hon heat. Upon inspection I found that the pressure switch port to inducer motor has blockage built up. Cleared the hose and the port. Turned system back on and system has been running for 35 minutes with no issue. System is running upon departure. Thanks for choosing LBA.

Installed new furnace, water heater and humidifier

We will be replacing the furnace and water heater and installing a new humidifier. We will also be installing a new drop and replacing the flu.

Switched to TO

Revised quote

Upon arrival the heat was not working. The thermostat was calling for heat but there was no movement at the furnace. I reset the furnace so I could see which error code it was throwing. The inducer motor started up and the igniter turned cherry ride like normal but the gas never released to start the flame and heat the home. I cleared the inducer hose and nipple that goes into the inducer collection box. After clearing the hose and nipple, the system started right up. I tested it 3 times to ensure it would start up on its own and it did. I did a temperature split as well to make sure the unit was not overheating and it was testing within manufacturer specifications at a 49 degree split. If you have any questions or concerns please feel free oto call us! Your LBA Technician, Tyler Rickard P.S. I took payment in the amount of $120.00 via CC for the trip and diagnosis today. Have a great holiday!

(*)*)()*(*)(*)*(*(*((&)*)=()=(*)&(&=;&(&=;=(;&(&(&)&) The itemized total comes in under the materials estimate. I cannot change it due to not having a line item that is changeable. Please change the materials to the estimate total of $1,369.00. Labor is correct. *)*(8*)*)*)*(&(*)(&)&)&(&(&((&(&(&(&(&(&((&( 11/26/24 Both tube heaters were put back into service. They both required new inducer motors and leak repairs. The motors were factory sourced and the repairs are covered by a one year warranty. Both units were cycled several times after the repairs were completed. The thermostat was left at 50 for the evening. Thank you, Jon Today I diagnosed the tube heaters that hang above the service alley. Both units have combustion blowers with seized bearings. I checked the incoming voltage to each motor as well as the units. The motors when unpowered are very difficult to turn. These motors are the first step in the heating cycle. Due to this I was unable to check the

L

L

L