Mission, KS HVAC & Plumbing Services

L

Arrived for furnace maintenance and inspection. I tested airflow and found the air pressure on the system to be over max so it’s considered failed. I changed filter and air pressure still failed. I tested for carbon monoxide and found the furnace to be pushing carbon monoxide into the home. I showed customer live readings and brought out field supervisor. I ran a camera to inspect heat exchanger and Lund that the heat exchanger had a hole and is cracked. We showed customer findings and we had to shut furnace down and red tag furnace due to safety failures.

Completed furnace maintenance and inspection. I checked all components and amp draws. I tested airflow and temp splits. I cleaned flame sensor, spark Ignitor and cleaned up furnace. I found no issues with system today. Filter needs changed and customer is changing that today. Furnace is operating within manufacture specifications at departure. Renewed membership and set up smart ac sensors.

*)*(&()&(&)&)&)&))&&()&(&(&)&(&)&)& Tp55A $159.00 Store to store transfer from Wichita ordered today 11/22/24 via key refrigeration. *(*((*((/()*(*(**((*()/((/((/( 11/22/24 Today I diagnosed the unit heaters that serve the service alley. Both units have combustion blower motors that have failed. The voltage to the heaters were checked and the motors were receiving power but not turning. They were unpowered and the shafts barely turned. In addition to this each tube heater has a small gas leak. The combustion blowers are the first step in the ignition process for these heaters. They will need to function before we can Tech notes: 12’ A-frame needed, tube heater (north)m/n DX2-30-100N, s/n 0408RWEN58604002, bad inducer, gas leak at flex line Tube heater (south), m/n DX2-30-100N, s/n xxx

Happy call

Went for a furnace inspection today. Did a static pressure test, it is failing. Did a carbon monoxide leak test, there is no leaks. Tested for gas leaks, no leaks. Combustion analysis test passed. Temp split between the supply and return duct passed. Inducer motor amperage passed. Gas pressure met factory specifications. Pressure switch passed. Exhaust flu is in good condition. Filter is clean and ducts are slightly dirty. Blower wheel is clean and blower motor amperage passed. Thank you for choosing LBA services!

Customer had a faulty, thermostat where you couldn’t even move the temperature and would stay constantly on even when the thermostat was satisfied the customer gave the options to replace customer went with the basic thermostat got it replaced unit is up and running as it should and turns off when thermostat is satisfied

Email

Quoted

Completed furnace inspection for customer. All aspects of system tested within manufacturer specifications. No recommendations at this time. Discussed cabinet rusting with customer and found that she did have some condensation issues after install. Took photos to document and monitor, inspected heat exchanger and one cell does have surface rust forming, all others clean. Will continue to inspect and document at future visits.

.

Went for a service call today. Furnace wasn’t coming after diagnosing the problem, I noticed the inducer wheel was stuck. I cleaned the debris out. The house is now heating. Thank you for choosing LBA services!

Estimate

Estimate

Na

Texted for an update

Presented on static pressure issues in the furnace and ducts. Recommended a 1,2,or 3 star solution. Presented finance options. Customer needs wife to be the decision maker. I left my information to call me if they are truly interested in repairing such a large issue as we’ve uncovered.

Went for furnace maintenance. When to test static pressure failing for system. Had supervisor came to retest and find solutions. All electrical components are passing for system. Cleaned out flame sensor, pressure switch, and drain line. Temp split passing for system. Heat exchanger has no cracks and sealed. No CO was detected when testing. System is up and running before leaving. Signed up customer with membership. Thank you for choosing LBA services-Johann.

Estimate

Arrived for furnace maintenance today. Furnace is 22 years old. Tested static, the max for system is .5 system is currently running at .76, failing static. Found crack in heat exchanger. Tested carbon monoxide and was getting 10 ppm. Red tagged system. Filed supervisor was out to discuss replacement options. Thanks for choosing LBA.

Sold furnace

Went for ac and furnace maintenance. When going to furnace tested for static pressure. System rated .8 for static. System operating at .6. Passing for system. Clean out drain line and flame sensor. All electrical components are passing for manufacture specifications. Did notice blower wheel is collecting dust. Will need a clean in the near future. Checked water panel does need to be replaced soon. Customer would like to hold off with options for now. Cleaned outdoor unit. Capacitor is passing and amperage for both fan and compressor. System is up and running before leaving. Thank you for choosing LBA services.

Customer wants home warranty

Went for a maintenance call today. When testing static pressure, it failed. After doing a CO leak, my meter detected carbon monoxide. I red tagged the unit and shut the gas off. thank you for choosing LBA services!

Changed the evap. Coil under warranty. Charged system to proper level. System is running as it should be at this time