Overland Park, KS HVAC & Plumbing Services

Arrived for furnace check today. System is 14 years old. Heat exchanger looks ok. Carbon monoxide test was 0ppm. Inducer motor is leaking. Inducer capacitor is almost out of range. Blower wheel is dirty. Solenoid for humidifier is bad. There was an 88 degree temp rise. All other electrical is running in spec. Repair solutions were declined at this time. Thanks for choosing LBA.

100k btu 96% 2 stage furnace sold for today

Installed new York Furnace-Y81E080B12SMPS1 Re-used existing thermostat Equipment Warranty 10 year Labor/10 year parts

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Found that the system is operating with excessive static pressure. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the fan for heating and cooling is coated in dust debris. Checked systems heat exchanger to ensure proper venting of flue gas. Found that the heat exchanger is failed and has multiple holes in multiple cells of the heat exchanger. This makes the furnace unsafe to operate because the furnace is venting carbon monoxide into the air stream. Reached out to a field supervisor to provide repair and replacement pricing. Replaced the solenoid valve and humidifier panel as part of the furnace replacement. Furnace is not operational at this time.

Floor Drain is backed up. I ran water through drains coming from ac and furnace. No issues. Checked for water in furnace but all hoses were tight. Floor drain didn’t drain when I poured a cup of water through the ac drain. Plumbers are scheduled this afternoon to clear drain.

Sold repair for shower valve entry through backside of shower and other bathroom. Main entry valve repair putting a ball valve above.

Went for a maintenance call today for heat. Tested for static pressure, system is passing when in heat for static. Did a combustion test is within specifications. Inspected heat exchanger did find heat stress in chamber. No crack or leaks were detected at this time. All electrical components are passing for manufacture specifications. Did clean flame sensor and pressure switch hose. Control board has no wear and tear. System is up and running before leaving. Thank you for choosing LBA services-Johann

Dispatched for furnace tune-up. The components that are tested during the tuneup are heat exchanger, flame sensor, igniter, blower wheel, inducer, temp split and combustion in the heat exchanger. The inducer motor bearing has lost some of the grease and is starting to rub. The inducer is the first safety check of the furnace. Replaced humidifier pad. Order a new inducer motor and will reach out to schedule a return to install and collect Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

Bid to complete the following - Remove all remaining galvanized water lines in basement - Replace removed lines with new crimp pex water lines - Replace undersized existing pex trunks with proper sized lines - Properly secure new and existing lines to prevent movement - Install new shower valve and shower head in basement - Drill through wing wall to add water supply to basement kitchen sink - Cut into existing main waste stack in basement to add drain for downstairs bathroom LAV - Run new water lines for new downstairs bathroom LAV - Run new water line for existing dish washer - Repair flu in basement causing water heater to backdraft - Add thermal expansion tank to existing water heater - Flush existing water heater after work on waterlines has been completed - Replace front hose bib - Add hose bib to rear of home - Replace anode rod in existing water heater - Replace upstairs bathrooms pop-up assembly - Removal of all excess jobsite debris and materials We have completed

Replace hydrant in back with frost free one

Dispatched for furnace tune-up. The components that are tested during the tuneup are heat exchanger, flame sensor, igniter, blower wheel, inducer, temp split and combustion in the heat exchanger. All components of the furnace are with in range of manufacture specifications. Recommend adding a condensation pump to the system to help with the collection of the condensation. This would allow to relocate the collection bucket anywhere. Also recommend a duct cleaning and blower wheel cleaning. Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

Dispatched for no heat. After a visual inspection and checking there was power. The system had an error code. The error code was for the water sensor. After disconnecting each terminal of the sensors and that they had a good connection. Then disconnected the plug from the board and check the connection was secure the code reset and the system began to operate. The system went through all stages of heating and is operating as it should. Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the fan for heating and cooling is coated in dust debris. Checked systems heat exchanger to ensure proper venting of flue gas. Found a large crack on one of the cells of the heat exchanger. This crack is absolutely big enough to vent carbon monoxide into the airstream, making the furnace unsafe to operate in heating mode. Performed an electronic gas leak search. Signed red tag with homeowner. Turned off the gas valve feeding the furnace. Field supervisor proposed repair and replacement solutions.

…

Pilot lit relit. Gas must’ve been shut off to water heater by accident during service