Overland Park, KS HVAC & Plumbing Services

I found today that the blower bearings are blown out of this unit and a bad belt. Need to replace and get the unit to a running point to see if this the only issues.sent photos to Rick for estimate

Customer called in needing someone to look at water softener. Upon arrival, customer stated that she’s been putting salt, but levels don’t seem to drop and would also like their whole home sediment filter replaced as well. Gave customer estimate to replace sediment filter and customer agreed. Installed new sidement filter for customer. Checked for leaks and no leaks detected. Checked the salt tank and salt is starting to bridge. Broke up all the salt and by time I was finished, salt levels dropped to below max fill line. Softener is still working but just needed salt to be broken up.

Rerouted low voltage and cut zip ties. No combustible near bvent

11-10-25 No heat call I spoke to Mel Sunday afternoon Today I found the flame rollout switch bad on the carrier rooftop unit. Started the heating system tested for any actual flame rollout. Had no issues, left the existing rollout switch in the unit. The system is running. I went and picked up a new flame rollout switch, and installed. System is working at this time. I called Mel let her know that work I did Carrier RTU See equipment list

Arrived for furnace check today. Static pressure is passing. Heat exchanger has a few rust spots to keep an eye on. Carbon monoxide test was 0ppm. There is a 60 degree temp rise. All electrical is running in specs. Blower wheel is dirty and will need to be cleaned soon. System is running upon departure. Thanks for choosing LBA.

T and p pin wasnt all the way back in.

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Found that the system is operating with excessive static pressure. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the fan for heating and cooling is starting to collect dust. Checked systems heat exchanger to ensure proper venting of flue gas. Found bacterial growth present on the evaporator coil. Performed an electronic gas leak search. Verified operation of the humidifier. Furnace and humidifier are operational at this time.

Flushed water heater. Prv is from 2018. Reccomended he keeps an eye on it. It’s getting up there in age.

Arrived for furnace check today. Heat exchanger looks good. carbon monoxide test was 0ppm. All electrical is running in specs. You have been changing filters. There is a 48 degree temp rise. We got sensors set back up. System is running at departure. Thanks for choosing LBA.

Customer had an issue of air bubbles spooning out one faucet in the house tightened aerator. Tested psi. 65. Looked at halo 5 main entry valve and water heater. Everything’s health in good shape

Arrived for furnace check today. Had to clean flame sensor first, system was not running. Once cleaned, system fired up and ran. Static pressure is passing. Heat exchanger is good. Carbon monoxide test was 0ppm. All electrical is running in specs. System is running upon departure. Thanks for choosing LBA.

*)*(*)*)*)&*))*)*)*)*)*))*)*)*)*))*))*))*)*)*)*)*)*)*) Please review and adjust as needed. 1hr estimate 0.75hrs finding the correct furnace and condenser on the roof 1.25hrs confirming call for heat and cool from t-stat and diagnosing the furnace. ))))(((. This does not include 20min drive time &)*)*))*)*)*)*))*)*)*)*))*)*)*))*)())()*)*)())()( Today I confirmed location of the furnace and condenser that serves the thermostat that is west of the reception desk. On the roof there are multiple condensers that are not labeled as well as a unit that has been disconnected in the past. I spoke with Shane and he asked that I check the system’s heating functions and continue with confirming the location of the equipment. I discovered that the furnace has a gas valve that is not opening when it receives voltage to operate. This furnace is approx 30yrs old and the condenser is 28yrs old. I relayed what I discovered that was preventing the furnace from heating. I also explained tha

Updated and emailed quote to customer

I inspected the furnace and checked all components and amp draws. I tested airflow pressure and ran a camera on the heat exchanger. I tested for carbon monoxide. Furnace is running within manufacture specifications. The air filter has been changed out since the noise was made by the system. Since I couldn’t find anything on the system or replicate the noise and the system hasn’t made any noise since the filter has been changed, I will have to assume that the filter caused the blower to ramp up in speed which caused weird noises from the ductwork.

.