Mission, KS HVAC & Plumbing Services

B

Went over different issues with both systems and multiple options . Kevin wants to get other quotes before making a final decision

Dispatched for 2 ac maintenance and 2 furnace safety checks. During the furnace inspection the furnace was operating for the first floor. During all furnace inspection we have a carbon monoxide detector operating during the inspection for your safety. After checking other components of the furnace the carbon monoxide detector start to detect CO in the air and continue to climb higher. At that point the system was red tag and gas turned off to the furnace. The second floor furnace components were in better condition than the first floor unit. There was no CO detected for this system. Only concern is the inducer motor. And signs of the ac coil freezing with water inside burner area. The 1st floor ac unit is operating with in manufacture specifications, the second floor ac is showing signs of a possible leak due to the refrigerant pressure not within range Thank you for allowing us in your house to provide the perfect home service and i look forward to y

Coming back tommorow to discuss all the issues with both systems while both Kevin and Sarah are home

Arrived to do a performance maintenance. Set system for cooling. Measured the systems static pressure and measured a temperature split between return and supply air. Found that the system is operating with failing static pressure. Checked interior of the furnace for cleanliness. Found that the blower wheel is starting to collect dust debris. Found that the evaporator coil is impacted with dust debris. Went outside and verified refrigerant levels. Verified operation of all electronic and mechanical components. Rinsed coil free of debris. Spoke with homeowner about the system. Recommend using filters with a filtration rating of merv 8 or lower. Filter is 20x30x1. Should probably be changed every 2 months. Air conditioning system is operational at this time.

.

Clean coil, uv light , cleaned house

Arrived for ac out. Upon arrival system was only running the fan. Switched to fan, outdoor unit was not coming on. I found the coil was very dirty and the capacitor had gone bad. I clean coil. Filter was also very dirty. With approval I replaced capacitor and filter. So for today you signed up on our family membership, replaced capacitor, and replaced filter. I got smart ac all set up. System is running upon departure. Thanks for choosing LBA

8-16-25. Spoke to Patrick earlier the issue is the showroom in the used. Car building is extremely hot. Upon arrival spoke to the gentleman at the desk, forgot his name. He did say they’ve had some power outages Showroom is extremely hot, thermostat was reading 92° I got up on the roof located to York RTU. There was only one rooftop unit the serial #N1E0842316 I found the board leaking the code ignition control failure. I’m pretty sure they were not running heat, but it may have locked out in this position when the power went out or had a power surge. I reset the unit electrically from the service disconnect. Let it sit for a couple minutes. Re-energize the unit. In a couple minutes. The unit came back on and is running in AC mode with both compressors. Not showing any fall codes unit run for about 15 minutes. While I was waiting, I went ahead and glued the 1 inch PVC P-trap fittings together. The trap is there, but nothing is glued. After a little bit, the system is running. I’ve

Told customer we can do a small repair to corroded piping underneath sink. If that doesn’t solve problem we may have a bigger project on our hands.

Water Heater Efficiency Check: I tested the water heater for performance issues. After calibrating the thermostat, checking insulation, and verifying the anode rod condition, the system ran more efficiently with better energy savings.

B

EST to dig

Went for a maintenance call today, tested for static pressure. System is passing when in cool. All electrical components are passing for manufacture specifications. Refrigerant pressure are passing as well for temp split. Did clean condenser unit and replaced filter. System is up and running before leaving. Thank you for choosing LBA services-Johann

Arrived to inspect a system in a home that has had mold. Used inspection camera to check the evaporator coil. Checked the ductwork for debris. Checked the interior of the furnace as well. Built estimates for duct cleaning and having uv installed. Mentioned that with the purchase of the duct cleaning we will also rinse the evaporator coil with coil cleaner. This way the coil and the ductwork will be cleaned and the uv bulb will stay in place to keep these items free of bacterial growth.

Found that the ahu2 had a lot of water coming out of it. I cleared the drain line. I went to run the system and the stat for this unit is missing and no one knows where it is. Also found the the outdoor unit has been shut off. This unit has not been running for some time and the water has came from a roof leak somewhere. At this time the unit is not running and they are ok with that. They will get with the home office about the communication stat for them to control from Texas.

Augered roler

Changed sump pump

Est

B

I worked on units 5,6, and 7. These units are not running as they should be due to lack of maintenance. I deep cleaned each condenser coil inside and out to get as much dirt and cottonwood out of them. Also all condensation drain are clogged. I cleared them and refilled the j traps. Changed the filters in each unit which had not been done for over a year. This area is for the shop and needs to have the fliters change at least every 3 months if not sooner. After that all system had a good temperature split. This all can be kept up with if they can get a PM set up so we are not spending hours to clean and common house keeping on all the units for this location.

Mini split

Took a $1000 off each system and asked to make sure he was happy with all the recent work. Let him know we took $1000 off each system in case he changes his mind and wants to replace instead. Left VM and sent a text.

Emailed estimates. High likelihood he will move forward in a couple weeks. Will follow up on 7/7

Arrived for ac check today. Started at furnace and checked static pressure, it is failing. Heat exchanger is starting to rust and has hot spots all over. Blower wheel is caked in dust. Motor amps are good. Temp split was only 16 degrees, 20 is where it needs to be. At the condensing unit the coil was caked in debris, I cleaned it. pressures and charge looked ok. Electrical components are running properly. Unit is out of level. Contactor is burnt. System is running upon departure. Thanks for choosing LBA.