Mission, KS HVAC & Plumbing Services

Attempted water heater flush. Was not successful sediment built up bad in the 19 year old water heater. Quoted for repairs in a new water heater and shut off Also tested prv responsiveness. Set pressure back to 60 as it is responsive and doing its job

Completed furnace, maintenance and inspection. I cleaned flame sensor and wiped down furnace. I tested amp draws and components. I checked airflow and temp splits. Airflow pressure is too high on the system, causing the system to run harder than it normally would. Customer is aware of the airflow situation. Furnace is operating at departure.

Martha’s neighbor who worked for united for 17 years is going to install the new furnace at less than half our cost

Arrived to remedy an inoperable system. Upon inspection of the system, found that the heat exchanger is damaged and the system is unsafe to operate. Spoke with homeowner’s neighbor who is a retired HVAC technician and trusted advisor to the homeowner. He is also able to corroborate this diagnosis. Reached out to a field supervisor to provide replacement solutions. System is in operable at this time.

Replace flu section.

Called to authorize installation of the uv bulb.

Went for a maintenance call today for heat. Tested for static pressure system is passing when in heat. All electrical components are passing for manufacture specifications. Did a combustion test is within range. Inspected heat exchanger no cracks/leaks were detected. Checked temp split and is passing. Did replace filter for customer. Cleaned flame sensor and pressure switch hose. System is up and running before departure. Thank you for choosing LBA services-Johann

Quoted work for prv and new shut off. Sent quote offered financing. He wants to speak with wife on it

No one home.

A 1:05 20x25x2 x 4. 5.91 20x25x1. X1. 5.16 Ignition board = tomorrow at noon $177.00 S1-6585821 Flame sensor = $31.09. S1-02535306000 $177(3.63) 642.51 31.09(3.63) 112.86 5.91(6.81) 40.25 [x4 filters] 40.25(4) = 160.99 5.16(6.81) 35.14 [x1 filter] = 35.14 Total $951.50 3hrs labor 10/27/25 Parts due in tomorrow at noon Cfm Lenexa already on will call under J#-001. Filters at cd jones already on will call need to give p.o. j#-002

Returned to install PRV. Went to crawl space to install PRV. Cut out section of pvc and replaced with copper. Installed PRV and set pressure to 75psi. Checked for leaks and no leaks detected. Checked expansion tank and expansion tank was at 50psi. Pressured to 75psi to match house pressure. 1 year warranty.

Customer called in about running toilet. Upon arrival, discovered that toilet was running. Checked flapper and noticed a plastic ring on it and removed it. Customer mentioned he replace the flapper, but want able to get it to stop running. Noticed chain was really long. Chain could be getting caught between flapper. Adjusted chain and flushed toilet several times and no more running toilet. Did notice fill valve wouldn’t stop filling when it was supposed to. Check water pressure and water pressure at 110psi. Per code pressure should not exceed 80psi. Will return next day to install PRV. Replaced fill valve and supply line. While replacing fill valve, noticed tank was loose. Bolt is missing on one side of tank. Informed customer of findings and customer approved for toilet tank to bowl bolts to be replaced. While installing new ones, tank ended up cracking. Went ahead and replaced entire tank at no additional costs due to breaking on us. Checked for leaks and no leaks detected.

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the fan for heating and cooling is beginning to collect dust. Checked systems heat exchanger to ensure proper venting of flue gas. Found bacterial growth on the evaporator pan. Performed an electronic gas leak search. Verified operation of the humidifier. Found bacterial growth in the evaporator panel. Furnace and humidifier are operational at this time.

Arrive for furnace check today. Furnace was installed in 2014. Heat exchanger looks good, no rust, holes, or cracks. Carbon monoxide test was 0 ppm. There is a 52 degree temp rise. Blower wheel is clean. All electrical is running in spec. I changed furnace filter today as well. System is running upon departure. Thanks for choosing LBA.

Dispatched for furnace tune-up. The components that are tested during the tuneup are heat exchanger, flame sensor, igniter, blower wheel, inducer, temp split and combustion in the heat exchanger. All components of the furnace are with in range of manufacture specifications. Recommend an indoor coil cleaning during the spring tune up. Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

**(*))*)&()*)&(*)***)**)*&*(&)(* Correct filter list for this location was forwarded to Elle (2) 20x25x1. (1) 18x24x1 *(*)*)&)&)&))&&&)&&&&&& Today preventative maintenance and heating checks were performed. The three natural gas furnaces were checked for electrical and mechanical heating functions. In addition to this each unit had it’s filters replaced and the flame sensor removed and cleaned. A checklist was completed and emailed for today’s work. Thank you, Jon

Arrived for furnace check on two systems. Main system has a rusty heat exchanger, very dirty coil, small return. It’s from 1996. You’re honking about replacing soon. The second system is 2018. Heat exchanger is ok. Static pressure is ok. Carbon monoxide test was 0ppm. All electrical components are running with in specs. Reach out when you’re ready to discuss system replacement! Have a good weekend!

..

I found that the system in the mechanic bay was tied into the condensation line of the abandoned unit in the drive threw bay and the water was going to that unit and filling the pan and over flowing. I cut the abandoned unit out of that condensation line and capped. Now the only one draining is that one unit in the mechanic bay. I also blew the line out with nitrogen to insure no clogs. At this time it is draining as it should be.

Completed full heating maintenance. Took amp draws on electrical components and changed all filter in all rtu's and washed filters in the mini split in the computer Server room. Everything is running as it should be at this time

Do not needed

-Remove wall to gain access to room under living room -Locate spot of sewer line that cable/camera can’t get past -Jack hammer open concrete under located spot on main sewer lateral -Remove damaged section of main sewer line -Use auger to snake rest of main sewer line open -Camera line to ensure proper function after cabling -Reattach main sewer line with proper fittings per code -Replace concrete -Note- Cannot guarantee wall can be restored but we will attempt to keep it as one piece.

B

Still waiting on a few more estimates from other companies before making a final decision

Went out for no flow. Cam proposed solutions.