Grandview, MO HVAC & Plumbing Services

Completed furnace inspection for customer. Components tested within manufacturer specification. Static pressure was failing running at almost double the value allotted. 2ppm of Carbon monoxide detected, inspected heat exchanger and it visually appears to be in good condition.

.

.

.

.

Sold iaq

X

Customer called stating system wasn’t operating properly. Found that the signal was breaking at the thermostat. Once corrected furnace ran for about 5 minutes and then flames continued dropping out and relighting, found that gas valve relay is faulty. Blower motor was leaking oil. Customer is opting to replace furnace. Turned over to field supervisor for further advisement.

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Found that the system operating with failing static pressure. Tried to relive enough static pressure to bring the system within manufacturers specifications, but was unable. Set up for a field supervisor to finish the diagnosis on Thursday at 2pm. Verified operation of all mechanical and electronic components of the furnace. Cleaned the flame sensor and retested its performance. Checked blower for cleanliness and to see if there is any play in the bearings. Checked systems heat exchanger to ensure proper venting of flue gas. Found rust present where the heat exchanger is prone to failure. Found lots of debris filling the cracks in the ductwork. Used the inspection camera to look inside the ductwork. Found excessive debris built up inside the ductwork. Furnace is operational at this time.

S

Went for a maintenance call today. Tested for static pressure. System is passing for static. Did a cfm count is short on supply. Based off going on national duct sizing. Did a co test, no co was detected when testing. Inspected heat exchanger no wear and tear. All electrical components are passing for system. Temp split passes for system. Drain line, pressure switch hose and flame sensor are clean. As well as blower wheel. No further wear and tear on system. Thank you for choosing LBA services-Johann.

S

Arrived for furnace maintenance today. Checked static pressure and found it is failing. A field supervisor is out to look further into that. Carbon monoxide test was 0 ppm. Heat exchanger has some rust forming. Blower wheel needs to be cleaned. All electrical components are running properly at this time. System is running upon departure. Thanks for choosing LBA.

12/4/24 - Completed a full heating maintenance on all equipment. All filters were changed, belts were checked, heat exchangers were checked, and proper operation was tested. Overall, all equipment was in good condition, it was running well, and there were no issues found at this time.

Installed an 80% furnace, communicating with furnace box and T-Stat

This system was installed correct for the condensation to drain proper. Old line was clogged that we were using. I reinstalled old condensation pump back into the new unit and ran lines to it. Ran system threw all functions and there is no leak anymore.

Sold

Sold

Sold

Sold

Unit has been red tagged due to co detection in the ductwork itself heat exchanger has been breached field supervisor is out to help

When system was installed drains on collection box for inducer were not set up for horizontal application.this caused the inducer to flood and not pull air thru the pressure switch. To fix this issue we will need to re run the drain line so we can get a good pitch and the furnace is draining for horizontal application.

Todd is having some health issues and needed to admit himself into the hospital. He will contact us when he can. In the meantime we hope that it is nothing serious, and that you get better soon! thoughts and prayers.

For this job, I was showing up because our tech Chase came across a leaking heat exchanger that was putting carbon dioxide into the air. After looking at all the options it is clear that the best way forward would be for system replacement. That way we could do 10 year parts and labor warranty on the entire thing. We could also flip the system so that is facing the opposite direction. Put a new return drop on it with a canon and a 2 inch separation from furnace to coil. We would also replace the Lineset. We can either do the entire system with a free UV light for 11,000. Or we could scrap the UV light and do a full system for 10,500. This is with a military discount and an additional 2000 off.

Came out to home to see why system was vibrating. Before diving into that I ran safety inspection on system. I found carbon monoxide coming into the home. I shut down furnace and ran inspection camera. I found hole in the heat exchanger and showed customer. Evap coil is full of debris as well as the blower. Brought out supervisor to confirm findings. Red tagged furnace and turned gas off to the furnace.