Blue Springs, MO HVAC & Plumbing Services

Performed inspection and presented 3 options for repairs. Follow up call scheduled for Monday

Completed furnace maintenance and inspection. I checked all components and amp draws. I tested airflow and temp splits. I cleaned up furnace, water heater, and flame sensor. While testing the air pressure on the system I saw that the system failed testing. System’s air pressure is over the max rating designated by the manufacturer. Upon further inspection I noticed signs from the system running over pressurized. The blower wheel is building dust and debris on it, the temperatures from the furnace are on the higher side of the specified range, and the blower is ramping up to try and compensate for the extra pressure it’s dealing with. Furnace is running for now.

L

L

L

L

Furnace tune up today check static pressure static was passing. Unit was about a year and a half old so everything was checking out on the unit replace filter, cleaned out flame sensor, took ohms and amps on all equipment made sure that the operations of the heating cycle we’re all working perfectly fine. Everything was good but everything back together. Unit is up and running. Thank you for choosing LBA

Completed furnace maintenance and inspection. I checked all components and amp draws. I tested air pressure and temp splits. I cleaned up furnace and flame sensor. Air pressure failed testing. This is causing higher temperature splits and causing the blower to ramp up extra to try and keep furnace from overheating. Ultimately it’s making the blower overwork. Supervisor arrived to check in on readings. We notified customer and explained situation with the system.

L

L

L

L

Went for a maintenance call today. When going to furnace tested for static pressure. System was passing. Did a carbon monoxide test, no co was detected when testing. All electrical components pass for manufacture specifications. Cleaned flame sensor and pressure switch hose. Blower wheel was clean. Temp split was passing for system. Heat exchanger had no wear and tear. System is up and running before leaving. Thank you for choosing LBA services-Johann.

.

Warranty ac

Went for warranty. Put In humidifier thermostat, humidifier is up and running again. Wired correctly for customer.

Upon arrival I began the furnace tune up. First, I did a static pressure test. This system is rated for a maximum of .5 static pressure and it tested at .45 which is passing. I then checked the running amps on 5e inducer motor and blower motor and both were within manufacturer specifications. The temperature rise was within range at 57 degrees. Humidifier is working properly and had water flowing to it. I replaced the filter today with a size 16x25x4 inch filter. I did notice the blower wheel was pretty dirty and I would recommend having it cleaned as your earliest convenience. I will include the estimate with the invoice sent to the email address on file. If you have any questions or concerns please feel free to call us. Have a great weekend ahead! P.S. No payment was due for todays visit. It was covered with your warranty.

Static passed. Cfm passed.

Went for a maintenance call today. Tested for static pressure. Static was passing for system. Did a carbon monoxide test no co was detected when testing. Heat exchanger had no wear and tear. All electrical components were passing for manufacture specifications. Drain line was clean. Condensation pump was not working. Will be replaced another day when available. System up and running before leaving. Thank you for choosing LBA services.

Went for a maintenance call today for furnace. When testing static pressure it’s a max rating. Replaced filter for customer. All electrical components pass for system. Did CO readings no carbon monoxide was detected. Cleaned out flame sensor, and pressure switch hose. Blower wheel was collecting dust. Temp split passes for system. System is up and running before leaving. Thank you for choosing LBA services-Johann.

Presented two options with customer today. One for furnace replacement. One for full system replacement. She had me email options today. Wants some follow up info tomorrow. Call has been added to my schedule for tomorrow.

Brayton says that her furnace may have been acting up before her maintenance service visit. Furnace exhaust is split, this will need to be replaced before the system can operate safely in heating mode. Indoor fan assembly is due for a deep cleaning. System is unprotected from electrical overload. Because of this we are offering surge protection for the indoor and outdoor units. Brayton said she wants to see what replacement looks like before putting any money into the old system.

Declined

Arrived for furnace maintenance today. Checked static pressure and found it was failing at this time. A filed supervisor is out to discuss options. Blower wheel is collecting dust and needs to be cleaned. All electrical components are running properly at this time. Ran a combustion analysis to make sure it’s burning fuel properly. Carbon monoxide readings were 0 ppm. Thanks for choosing LBA.

Static decline