Blue Springs, MO HVAC & Plumbing Services

Estimates cb

Installed add a wire kit. All modes work… heat, cool, fan only. Thank you for choosing LBA services!

G terminal doesn’t haven’t a wire. Not getting a signal from the thermostat, due to not having a wire. Thank you for choosing LBA services!

Estimates tankless install

Completed furnace maintenance and inspection. I checked all component and and amp draws. I tested airflow and temp splits. I cleaned flame sensor and cleaned up furnace and water heater. 2 yr old furnace is running within manufacture specifications. Only concern with the system is that there is no surge protection on the system. Spoke with customer about adding extra protection for the system. Customer would like to think about it for now. Thank you for your time today.

Customer had a new thermostat sitting on the counter and wanted that installed. I installed new thermostat and when I turned the temperature up on the thermostat, the thermostat would glitch off and back on. I went down to the furnace to reconfirm diagnosis. I ended up finding out that the humidistat wire had worn against the metal ductwork which exposed bare wire. The bare wire was touching the metal which grounded out the system. This is why the heat wouldn’t work. After I fixed wiring, the system ran as it should. Air filter needs changed out asap.

Install new Full System

Arrived for furnace out. Upon inspection there was a code for wiring issue. I put in a new fuse and changed thermostat. Board was getting power to it, there was a call for heat, but furnace was not turning on. The board is bad. We will be ordering the new board on Monday and calling to come install. Thanks for choosing LBA.

120k btu, 80% single stage furnace and 14 seer ac coil sold. Standard series full system

Arrived to do a performance maintenance. Set up for combustion analysis, temperature split, static pressure test, and carbon monoxide tests. Found that the system is operating with failing static pressure and is on the verge of overheating. Found carbon monoxide in the air stream. Reached out to a field supervisor to finish the diagnosis on the systems static pressure and verify the carbon monoxide content in the airstream. Verified operation of what components I can test without running the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found the blower wheel is heavily coated in dust debris. Checked systems heat exchanger to ensure proper venting of flue gas. Found large damage and excessive amounts of rust. Performed a retest, with the field supervisor, to verify the carbon monoxide content and found that both meters are reading unsafe levels of carbon monoxide. Furnace is disabled at this time.

Checked back in with customer regarding full system replacement needs. They can’t do the replacement now but will probably later this year as we continue their maintenance.

Went for a furnace inspection today. Did a static pressure test, it failed. Filter is clean. Did a carbon monoxide and gas leak test, no leaks. Combustion analysis test passed. Inducer motor amperage passed. Gas pressure and pressure switch passed. Flame sensor was cleaned. Blower motor amperage passed and blower wheel is slightly dirty. Thank you for choosing LBA services!

L

L

L

L

Working with customer on system needs. Returning on Thursday 1/30 at 12:30 to help with system changes.

Completed heating tuneup. Heat pump wasn’t running. After further diagnosis I found the unit over pressurized causing the high limit to trip. I recovered refrigerant and system ran as it should. Indoor unit does have bacterial growth and rust throughout.

Installed humidifier line and drain for humidifier. All operations are running well at departure.

Replaced thermostat

Completed furnace maintenance and inspection. I checked all components and amp draws. I tested airflow and temp splits. I cleaned up flame sensor and furnace. I changed out air filter. Systems air pressure is pretty high. Supervisor came out and confirmed ductwork is shorting the furnace on airflow. Furnace is running at departure.

Customer had a time constraint during tune up. RTP scheduled for Monday 2/3 to discuss airflow needs

Installed two new furnace and new humidifier

Completed furnace maintenance and inspection. I cleaned up furnace and flame sensor. I tested temp splits and air pressure. Furnace is running well. Recommended changing the filter more often since when I arrived the filter was causing really high pressure readings. After changing filter the pressures were under the max.

Spoke with customer