Overland Park, KS HVAC & Plumbing Services

7-29-25 Pool Room Dehumidifier system is not working. Room is at 95° currently. Found a system was in high-pressure alarm reset the alarm at the thermostat got up on the roof check the condenser unit. It was running properly good to airflow. I have a good 4.5ma call Not sure why it shut down pressure look good my super heat is high but there may be a potential leak that we gotta deal with down the road. The sightglass on the receiver tank and the liquid line are both clear I did notice that the pool boiler was not running today. Pentair pool boiler does have a code of 126 indicating a shorted temperature sensor. I’m gonna locate a sensor and get back with them.

Added a $50.00 credit to the account for future use

Sold job

B

***(*******(*(*((*************(((((****** The ionizer was removed today and returned to Marla. There is a note about charging her extra for doing such. The ionizer was not turning when I opened the compartment. However the light was green which indicates that it is functioning. Marla was informed of this condition when I returned it to her. **)**)*;*;*;&*;&:*&****(*)*)*(*)*)*)*** Today maintenance was performed on the Carrier rooftop unit that serves the salon. Filters were replaced, the condenser coil was washed, the drain was flushed and refilled and the system was operated while checking the electrical and mechanical functions. The ionizer was removed from the blower compartment and returned to Marla today. During maintenance it was discovered that one of the contractors had just started to show wear. There was no voltage drop across it and it did function normally however I did create an estimate for its replacement since it is a wearable part and it will continue to w

Replaced condenser fan motor. Everything working upon departure

-Repipe sump pump discharge line to eliminate the Fernco coupling Thanks for choosing LBA Services! Jeremy

We need to replace the condenser fan motor

B

Arrived for water leaning at furnace. Upon arrival I found that the drain trap was very dirty and water was standing in drain. I ran wire brush down trap and that unclogged all the mess. All the water drained out. I ran lots of through coil and drain to make sure it was draining properly. It’s good now. There is 19 degree split between return air and supply air. System is running upon departure.

Est to dig

Arrived to remedy an inoperable system. Upon inspection of the system found that the breaker for the furnace portion was tripped. Replaced furnace filter. Inspected furnace and didn’t find anything out of the ordinary. Reset the breaker and the system started cooling like normal. Performed diagnostic to figure out what caused the system to trip the breaker. Was unable to find anything that would cause the breaker to trip. Went outside and inspected the outside unit, looking for causes. Did not find any provable causes of the breaker tripping. System is operating within manufacturers specifications at this time.

I found the door to the compressor and coil area off of the unit. It had tripped on high pressure due to this. I reset and used jumpers to to the function of the unit due to no one on site to test from stat. This unit is running as it should be at this time after I put the door back on the unit

Arrived to replace filters and inspect outside units for cleaning. Filters had been in place for 3 months and are due to be replaced. Changed out filters and kicked each system on to verify operation. Went outside and checked the two condenser coils. These coils are still very clean, and do not need rinsed again. All systems are functioning properly at this time.

(7-25-25) Today the new thermostat and it’s equipment control module was installed and programmed. The programming intentionally excluded the remote sensor for the adjacent classroom and daily set point programming. These functions will be enabled and checked once the new remote sensor arrives (has been ordered factory direct from Carrier). The new thermostat is locked. The unlock process is very simple and I left a paper with instructions with the on-site manager today. The unlock process is hold both the up and down arrows for 10 seconds. Today (7/24/25) I was able to contact Carrier regarding system #4. To date we have been unable to observe the system when it intermittently switches to heat mode. This is a communicating controlled system that utilizes a split thermostat and equipment control set-up. Carrier’s tech support confirmed and recommended a replacement of the thermostat and the room temp sensor that is in the room adjacent to the thermostat. Below is