Overland Park, KS HVAC & Plumbing Services

12-12-25 The east garage area direct fire heater is not working. Upon arrival, I turned the disconnect on blower motor came on and started humming found the 3 pole disconnect switche bad one leg was not pulling in. I was able to work to switch on and off until all three steps made a good connection you still need to replace this disconnect. Start the system blower motor came on properly thenI was getting a failed ignition module (3 blinks). I was getting 24 V out of the module to the gas valve after tracing the wiring down. I found that the high limit manual safety was tripped. I reset the limit system came on, but also it tripped off again on me. I found the damper wasn’t fully open. I’m pretty sure the damper motor drive motor has failed, currently is it is locked open. At this point, the system is ruuning. we need to get a proposal for the disconnect. There’s still a belt that needs to get replaced and also look in replacing the damper drive motor. See pictures for the Model and

Preformed routine maintenance on furnace. All checks were within manufacturer specifications. Inducer is noisy but not over amping. Blower wheel is slightly dirty

Estimate

Furnace kicked on and ran when I arrived so I performed a three point safety inspection on the furnace. Furnace passed the safety inspection today. I made the system restart and when I restarted the system, I found that the gas valve is working intermittently. I I showed customer pictures and readings I received during the safety inspections. We also talked to options for repair and replacement. Customer would like to take some time to think about which direction they would like to go. I gave them my card in case they have any questions or would like to have us back out. Furnace is working intermittently at departure.

Went for a service call on humidifier. Water panel was dry. Water is coming from shut off valve. Checked solenoid valve and does allow water to flow through. Tech support confirmed of a faulty part, will replace under warranty. System is up and running for humidifier. Water is flowing freely when testing. Thank you for choosing LBA services-Johann

Arrived for humidifier not working. Got it wired up to work. No there is hardly any water flowing. Will have to be back again to fix water line.

Returned to replace left side water heater. Removed and hauled away old water heater. Installed 50 gallon Bradford White water heater. Installed new shut off valves for humidifiers. Installed new gas line as well. Checked for leaks and no leaks detected. 6 year tank & parts warranty. 1 year labor warranty

Arrived for furnace check on two systems. Started on upstairs system and static pressure is ok. Heat exchanger is good. Carbon monoxide test was 0ppm. All electrical is in range. I changed filter and humidifier pad. Blower has some dust build up. The main floor system static pressure is ok. Heat exchanger has some hot spots forming. Carbon monoxide test was 0ppm. All electrical is in range. I changed filter and humidifier pad. Both humidifiers are working properly. Systems are running at departure. Thanks for choosing LBA. Happy holidays!

Removed 2" and replaced with 3".

Approved estimates over the phone

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Checked systems heat exchanger to ensure proper venting of flue gas. Verified operation of the humidifier. Found that the humidifier panel is coated in calcium buildup. Found that the uv system is due for its replacement Uv bulb. Spoke with homeowner about the system. With homeowners approval renewed their membership and replaced the humidifier panel, as well as replacing the uv bulb. Furnace humidifier and Uv system are all operational at this time.

Arrived to do a performance maintenance. Upon arrival found that the steam humidifier is not operational. Opened the unit up and started diagnosis with the air of Aprilaire tech support. Determined the humidifiers control board and the control panel need replaced. Coordinated with office to provide repair and replacement solutions. Set up for combustion analysis temperature split and static pressure tests. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Checked systems heat exchanger to ensure proper venting of flue gas. Furnace is operational at this time.

Went for a maintenance call today for heat. Tested for static pressure system is passing when in heat. All electrical components are passing for manufacture specifications. Did a combustion test is within range. Inspected heat exchanger no cracks/leaks were detected. Checked temp split and is passing for specifications. Did replace filter for customer. Cleaned flame sensor and pressure switch hose. Checked humidifier water panel and needed to be replaced customer approved.System is up and running before departure. Did sign up for membership today and payment was collected. Thank you for choosing LBA services-Johann

Arrived to do a dual system performance maintenance. Set up for combustion analysis temperature split and static pressure tests for each system. Found that the main floor system is operating with excessive static pressure. Verified operation of all mechanical and electronic components of each furnace. Checked blowers for cleanliness and to see if there is any play in the bearings. Found that the main floor system is collecting dust debris. Checked each systems heat exchanger to ensure proper venting of flue gas. Verified operation of the humidifiers. Furnaces and humidifiers are operational at this time.

Completed furnace, maintenance and inspection. I cleaned flame sensor and wiped down furnace. I checked components and amp drawers. I tested air pressure and temp splits. Air filter needs changed out as soon as possible. Blower wheel is starting to build up dust. Once filter is changed out the air pressure on the system will drop down quite a bit. Furnace is operating within manufacturer specifications at departure.