Lee’s Summit, MO HVAC, Plumbing & Electrical Services

Installed new zone board, reprogrammed the board and the thermostat to operate correctly with the board.

B

Inspection

Went for off line thermostat. Reconnected thermostat system is now paid and works when calling on the app. Thank you for choosing LBA services-Johann

Arrived for ac check on two systems. I cleaned the coils on both. Refrigerant levels are good. All running amps are good. There is a 20 degree temps split on both. Systems are running as should be. Thanks for choosing LBA.

Today when I arrived I checked in with Scott. He was receiving an alert that rtu#3 was not functioning. I accessed the roof and located rtu#3. The unit was not functioning due to the integrated resettable fuse in the transformer, the fuse was reset and the system was operated. The blower motor contactor was chattering intermittently. I checked the control side of the unit and discovered that the contactor for compressor #1 was pulling the voltage down. In addition to this compressor #2 contactor was also in really bad condition. Replaced both of these after tracing voltages and amp draws through the low voltage components. The system returned to operation after the repairs and the blower motor contactor quit chattering. The amp draw at the 24v side of the transformer dropped to 0.98 amps during first stage cooling. I also discussed with Scott that the outdoor fan relay was also in poor condition. I will be addressing this with Sherry when she returns from vacation. Thank

Went for a maintenance call today. Tested for static pressure, system is passing when in cool. All electrical components are passing for manufacture specifications. Temp split is passing for system. Refrigerant levels is within range. Did clean condenser unit. As well replaced filter. System is up and running before leaving. Thank you for choosing LBA services- Johann

Installed new furnace

100k btu , 80% single stage Goodman furnace sold for tommorow

Went for an out on system. Drain line was clogged, did notice blower wouldn’t kick on. Tested capacitor and has failed. As well blower motor was water around the module hasn’t burnt out. Will need to replace both to have system running. Looked at heat exchanger noticed heat stress around the furnace.

System is low on refrigerant. Checked the txv and that is operating correctly. Did a refrigerant leak test on the cool and filter dryer no detection or refrigerant oil marks.

8-21-25 2 hrs RTU #18 Performed quoted replacement of the service disconnect. Quote to replace the rotary style line voltage disconnect in the Lennox package unit serial 5614C02801 marked as #18. Price includes the factory replacement parts and labor.

8-21-25 RTU #11 6hrs Performed quoted leak repairs to the refrigeration system RTU #11 has a refrigerant leak at the elbow coming off the compressor discharge This quote is to remove that elbow and reconfigure, the elbow has a lot of pressure and vibration. Test the system and recharge new refrigerant.

8-20-25 RTU # 18 has tripped off again RTU #11 is not Spoke to Sherry upon arrival I found RTU number 18 tripped the main circuit breaker and then found the unit disconnect which is burnt up. I will give a quote to replace the disconnect switch. RTU#11 It has a refrigerator leak at the compressor elbow. I will do a quote to repair also to reconfigure the piping to prevent vibration and stress. We submitted two separate quotes

Arrived to do a performance maintenance. Set system for cooling. Measured the systems static pressure and measured a temperature split between return and supply air. Found that the system is not moving enough air to match the tonnage outside. Adjusted the fan speed closer to spec to allow the system to operate properly, but not so high that the static pressure will cause issue. Checked interior of the furnace for cleanliness. Went outside and verified refrigerant levels. Calibrated the refrigerant levels to meet the new airspeed. Verified operation of all electronic and mechanical components. Rinsed coil free of debris. Spoke with homeowner about the system. Air conditioning system is operational at this time.

Arrived for ac check today. Started at furnace and checked static pressure, it is now running under the max. I did lower the cooling speed one speed tap. By doing this we are now moving the right amount of air, motor amps dropped, temp split went from 18 to 21 degrees. Blower wheel is clean. At the condensing unit I cleaned coil. Pressures and charge look good. Compressor and fan amps are good. Capacitor tested in range. System is running upon departure. Thanks for choosing LBA.

Duct Clean Blower Wheel Clean Level Condenser

-Removed corroded pipe to washer machines and Repiped with new copper pipe and pro press fittings -Replaced expansion tank with a new thermal expansion tank for water heater and Repiped to mount expansion tank to wall -Replaced PRV with new Watts PRV with a new main entrance ball valve shut off Thanks for choosing LBA Services! Jeremy

Arrived for ac out. Upon arrival system as off. Turned system on and the outdoor unit did not come on. I found the capacitor had failed and was not starting the system. I also saw the coil was caked in dirt and debris. I cleaned coil. With approval I replaced the capacitor. Restarted system and everything came on. System had a 19 degree temp split which is good. System is running upon departure. Thanks for choosing LBA.

Installed new uv system and added a double return air

Bad check valve and small gas repipe

***((*****(******(*****(********(*** 5hrs across both odf replacements ***)*;**;)******(*)(**)*)*)*))*)*) The outdoor fan motor, fan blade and matching capacitor (south motor) was replaced today. Before the repair I confirmed that the existing fan motor was not functioning. During the new motor installation I noticed that the plastic fan shroud had been cracked (not entirely uncommon for this model). The fan shroud was secured by adding a couple of self tapping screws. The unit was operated after the repair and is now back in service. Of note: during todays repair it was noticed that the drive belt for the indoor blower wheel has started to wear into the pulley. At this time the drive belt is functioning. Thank you, Jon Quote to replace the failed condenser fan motor on the Lennox package unit serial 5613M02670 marked as #14. Price includes the factory replacement condenser fan motor, condenser fan blade, run capacitor and labor.

**((*****((******((**(((((*((((*((((*(( 5 hrs between the two odf replacements *((******(******(*****************(** This unit had it’s south condenser fan motor, fan blade and capacitor replaced and function checked. Before the repair the failed fan motor was checked to confirm that replacement was needed. The motor mount for this motor was loose and a nut had vibrated off and was in the bottom of the unit. The motor mount was removed to climb into the unit and then it was reinstalled and tightened firmly. The new motor and blade returned this unit to service. All panels accessed today were securely attached and I walked around the unit to confirm that no screws were on the roof. Thank you, Jon Quote to replace the failed condenser fan motor on the Lennox package unit serial 5613J07033 marked as #16. Price includes the factory replacement condenser fan motor, condenser fan blade, run capacitor and labor.

Went for an AC inspection today. Filter is clean. Temperature split between the return and supply duct passed. Evaporator coil is clean and rust free. Leak detection sensor is in good working condition. Outside system got washed. Refrigerant pressures met factory specifications. Compressor and fan motor amperage pass. Capacitor passed as well. AC is up and running upon completion. Thank you for choosing LBA services!

Sending over estimate for ductwork and UV light germicidal unit