Kansas City, KS HVAC & Plumbing Services

*)*(&)&&)&)&)&)*)***)*))**)*)*)*)**)*)*)*)*)* Part available for order at Johnstone (p/n 5H0735980001) *)&)&)**)*)*))*))*)*))*(&)*)*()*)*)*)*)*)*))*)*)*)*))*)*)*)*)&) Today I arrived on-site and checked in. The unit heater that was heating does have a responsive thermostat. The gas valve, ignitor, fan motor, fan motor bearings and supply voltage was checked. The ignition sequence failed to complete due to a bad inducer motor. The voltage to this motor was confirmed to be in proper range. I spoke with Jeremy about the condition of the flue pipe and was given approval to remove it to check for any obstruction with the motor’s wheel and bearings. No obstruction was discovered this motor will not return to service. I relayed my findings to Kristi after sourcing a factory replacement and an estimate for the repair was also created and emailed due to the part not being available in the Kansas City area. Shipping is estimated at 2-4 business days Thank you, Jon Tec

Arrived for fan not shutting off on furnace. I checked fan settings on thermostat and found they were set to run the fan all the time. I set fan to auto, cycled system a few times and fan did not run after heating. System is running properly. Thanks for choosing LBA.

Dispatched for a no-heat concern. Upon arrival, the system was operating and providing heat as designed. A full system inspection was performed to identify any recent faults or conditions that could have caused the issue. During the inspection, the furnace control board was checked for stored fault codes. The most recent error code indicated a high-limit fault. This fault typically occurs when the furnace senses excessive heat, commonly due to restricted airflow, elevated supply air temperatures, or insufficient heat removal from the heat exchanger. At the time of today’s inspection, the blower motor was operating properly and airflow was within acceptable parameters. Supply air temperatures were measured and confirmed to be within the manufacturer’s recommended temperature rise range, indicating the system is currently operating safely and efficiently. No active faults were present during today’s visit. The system was left operating normally, and continued performance should be mon

Arrived to remedy a furnace that isn’t heating properly. Upon inspection of the system found that the furnace would overheat within about 5 minutes of operating. Performed diagnostic and found that the system is dirty and this debris is impeding airflow, keeping the furnace from operating at a normal temperature. With homeowners approval performed a blower cleaning. Cleaned out the base of the return. Performed an evaporator coil cleaning as well to allow the system to move air unimpeded. Tested systems heat exchanger operations and was able to lower the fan speed and the system is still operating within specifications. Furnace is heating properly at this time.

Installed new humidifier

Today I checked two Air-handlers that provide cooling only. Their condensers were also checked. The split-system that provides both heating and cooling to the front office area was checked for both heating and cooling functions. New air filters are due for the air handlers and the furnace. The unit heater in the warehouse area was checked today and was not functioning correctly. Verbal approval was given to diagnose this unit today. The Reznor hangin unit heater was not operating today when I arrived. It was diagnosed as having a high temp limit switch error. The system was reset and operated and about 3mins into operation it shut down on a high temp limit. The circuit for the temp limits was checked and they all were closed with no resistance. The plug on the main board was removed and inspected. The system was restarted and it jumped into heat mode and operated properly. The fan delay after the thermostat was satisfied was also checked and was ok. The heater was a

Snaked kitchen drain

Went for a service call on thermostat. System was running, did check inducer and blower are with manufacturer specifications. System is draining properly. Temp split for system is passing. System is up and running before departure. Thank you for choosing LBA services-Johann

Install customer provide Bosch 110 thermostat.

Arrived to check on humidifier. Humidifier was not functional at this time. We are going to install a new bypass humidifier and new water line. While here I did a check on your furnace. It’s from 2003. Heat exchanger has lots of rust. Carbon monoxide test was 0ppm. System is running safe at this time. We need to have the heat exchanger checked for sure next year. We will be out on Dec. 23rd for humidifier install. Thanks for choosing LBA. Merry Christmas!

Went for an out on system. Check power onto system was receiving correct power. Did jumper system no response when doing so. Did confirm board on furnace went out. As well inducer motor in the process was grounded.Did replace system is up and running before leaving. Thank you for choosing LBA services.

Today the light maintenance was completed (12/19/25). The filters were replaced, the burner compartment was visually checked, the blower wheel bearings are good and the drive belt along with it’s tension is also in good condition. The rooftop unit was put back in service after today’s work. Thank you, Jon Tech notes: Lennox: M/n KGA072S4BH3Y S/n 5615K05633 Belt size A41, good Blower wheel/bearings good Filters replaced

Warranty

This task will be attempting to get the broken piece lodge into the shower head and adding a new shower arm.

Completed lite maintenance

Today I did a lite maintenance on a single furnace changed n dated filter and verified unit working and operating properly.

Unit number 1 rtu is not running. I ran the system and it is getting gas, spark and the inducer motor is running but no fire. I did see that the unit has a new heat exchanger, gas valve, inducer motor and flame rails. I spoke with them about this and someone else had replaced those items not to long ago and they were going to contact them about this unit. There was no signs of this unit ever running in heat no discoloring no signs of any flames. At this time this unit is not running and they will be in contact with us once it’s running for a pm contract.

Water service quote

Went for an out on system. Checked error codes presented on system. Code was 93 for internal control fault detected. Per tech support is a bad board on system. Will need to be replaced. Customer approved replaced board system is up and running before leaving. Thank you for choosing LBA service-Johann

Dispatched for furnace tune-up. The components that are tested during the tuneup are heat exchanger, flame sensor, igniter, blower wheel, inducer, temp split and combustion in the heat exchanger. During the inspection some components have fallen below acceptable rating and would highly suggest repairing. The inducer is failing, the blower motor is out of spec and heat exchanger showing wear for the age. At the moment the system is operating. Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

Dispatched for furnace tune-up. The components that are tested during the tuneup are heat exchanger, flame sensor, igniter, blower wheel, inducer, temp split and combustion in the heat exchanger. For a 20 yr old system the components are in great working form. One concern that did rise is the blow motor with the excessive amount of dust build up around the motor. This is creating it to over amp and work harder. Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

Went for an out today. Upstairs unit was not operating. Checked wiring and voltage both were passing. Thermostat wasn’t sending signal to unit. Did replace thermostat system is up and running. Ran multiple times no issues. Thank you for choosing LBA services-Johann

Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and flame sensor circuitry. • Checked venting system for proper draft, secure connections, and obstruction-free flue path. • Tested carbon monoxide levels at the supply, return, and flue to ensure safe operation. Burner & Combustion System • Cleaned burner assembly and verified prope

12-9-25 Located two weeks an additional leak in the boiler tank feed parts on order probably gonna be going back on Thursday to make repairs

Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and flame sensor circuitry. • Checked venting system for proper draft, secure connections, and obstruction-free flue path. • Tested carbon monoxide levels at the supply, return, and flue to ensure safe operation. Burner & Combustion System • Cleaned burner assembly and verified proper ignition and flame stability. • Cleaned and tested flame sensor for accurate microamp readings. • Inspected igniter for wear, resistance, and proper operation. • Checked gas valve operation and confirmed proper inlet and manifold gas pressures. • Performed full combustion analysis and verified CO, O₂, excess air, and stack temperature are within manu