Kansas City, KS HVAC & Plumbing Services

Upon arrival, I addressed an inoperable system. The homeowner had partially removed the cover, which I fully removed to inspect. I discovered the condensation pan was filled with refrigerant oil, indicating a complete loss of refrigerant. After discussing with the office, I confirmed that the unit's evaporator coil is not serviceable. I contacted a field supervisor for replacement pricing, comparing options between a similar unit and a Mitsubishi mini-split system. The Mitsubishi mini-split system is scheduled for installation next week.

….

I performed a thorough furnace tune-up to ensure safe, efficient, and reliable operation. This included inspecting the heat exchanger for cracks and corrosion, verifying safety controls, and checking venting for proper draft. I cleaned the burner assembly, tested the flame sensor, and performed a full combustion analysis. The blower wheel was inspected for dust, and airflow through ducts was confirmed. Electrical connections were tightened, and thermostat functionality was tested. The system was run through a complete heating cycle to ensure smooth operation.

I was scheduled to install a new kitchen exhaust system. I arrived on time, prepared all necessary tools, and began by inspecting the existing setup. After ensuring everything was in order, I started the installation process, which included precise measurements and careful wiring. Unfortunately, I fell ill and had to cancel the job midway.

Upon arrival, I conducted a comprehensive evaluation of the HVAC system, inspecting the outdoor condenser, indoor evaporator coil, refrigerant line set, blower assembly, and electrical components. The evaporator coil was found to be punctured, leading to refrigerant loss and system inefficiency. Given the severity of the damage, the coil was deemed irreparable and required replacement to restore proper operation. Further inspection revealed that the existing refrigerant line set was undersized for the system's refrigerant type and capacity, which could cause improper refrigerant flow, reduced efficiency, and increased compressor strain. To ensure optimal performance and longevity of the new coil, I recommended replacing the line set as well. The recommended repair includes replacing the evaporator A-coil, installing a properly sized new refrigerant line set, evacuating the system to manufacturer specifications, recharging with the correct refrigerant, and verifying system performance.

N/a

I performed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation. I inspected the heat exchanger for cracks and corrosion, verified safety controls, and checked the venting system for proper draft and obstruction-free flue path. I cleaned the burner assembly, tested the flame sensor, and inspected the igniter. I balanced the blower wheel, checked electrical connections, and verified thermostat functionality. I also cleaned ignition components and replaced the air filter. After a complete heating cycle, I confirmed smooth startup and stable operation, ensuring the system is safe and within manufacturer specifications.

We completed a new construction project involving the installation of water lines. We began by creating a detailed layout of the house to determine the optimal path for the water lines. Coordination with contractors was essential to align the start and finish dates. We ensured the city set the meter and prepared the pipe for installation by sleeving it and stubbing it through the walls. This meticulous planning and execution ensured a seamless integration of the water lines into the new structure.

The customer had a leak going downstairs into the basement from the master shower the tile is cracked and the shower valve is loose. We checked all the drains and water lines no active leaks the only possible thing we can think of causing the moisture is the tile.

Dispatched to perform a full heating maintenance on a 3-year-old air handler equipped with electric heat strips. System is relatively new and overall in good operating condition at time of service. Performed a complete inspection and preventative maintenance on all major components of the air handler and electric heat assembly. Verified proper voltage to the unit and inspected all high-voltage and low-voltage electrical connections. Checked contactors, relays, sequencers, and heat strip wiring for signs of overheating, loose connections, or discoloration. All connections were tightened and confirmed secure. Inspected electric heat strips for proper operation and even heat distribution. Verified amperage draw across each heat bank and confirmed readings are within manufacturer specifications. No visible damage, hot spots, or fractured elements observed. Confirmed proper staging of heat strips and correct blower engagement during heat call. Blower motor and wheel were inspected for de

Completed a full heating system inspection and performance evaluation. The furnace is approximately 20 years old, which places it well beyond the average life expectancy of 12–15 years for most residential systems. During today’s tune-up, several concerns were identified: • Flame Sensor: Sensor was removed and cleaned due to improper microamp readings. After cleaning, readings improved slightly but are still weak and below optimal range, indicating the sensor is near failure. A weak flame sensor can cause intermittent shutdowns and nuisance lockouts. • Hot Surface Igniter: The igniter is testing below manufacturer threshold specifications. This indicates deterioration of the element, increasing the risk of a no-heat situation if it fails completely. • Burner Assembly: Burners are heavily corroded and beginning to break down. Corrosion affects flame carryover and proper combustion, which can lead to delayed ignition and unsafe operating conditions. • Debris in Burner Tubing: Excess

Customer called in needing quotes for a water heater replacement. Customer water heater is leaking from T&P valve. Checked water pressure and water pressure at 75psi. System does not have an expansion tank. Water heater is 20 years old as well. Gave customer estimates on repairs to replacement. Customer wants to go over rest of estimates and will make a decision by next week.

Went for a maintenance call today for heat. Tested for static pressure system is passing when in heat. All electrical components are passing for manufacture specifications. Did a combustion test is within range. Inspected heat exchanger no cracks/leaks were detected. Temp split and is passing for specifications on furnace. Did replace filter for customer. Cleaned flame sensor and pressure switch hose. System is up and running before departure. Thank you for choosing LBA services-Johann

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Made a adjustement to the systems gas valve to allow for better combustion of gas and keep the system from overheating. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the fan for both heating and cooling is collecting dust debris. Checked systems heat exchanger to ensure proper venting of flue gas. Furnace is operational at this time.

Customer is going to make it through the rest of the year before replacing furnace

Found seal around roof jack and flue letting water into house. Roof cap is not allowing Hot air to escape causing moisture to run down pipe thru the seal and into house. Roofers shoukd reseal the connection and repace cap and section of pipe

Completed furnace, maintenance and inspection. I cleaned flame sensor and wiped down furnace. I tested air pressure and temp splits. I tested components and amp draws. I ran a combustion analyzer test and carbon monoxide test. As of today, the 15 year-old furnace is running safely however there are multiple signs of the heat exchanger giving out. I showed customer the safety concerns. I recommended to get low level detection carbon monoxide detectors. Customer would like to wait on taking care of the furnace situation for now. I offered our membership to continue maintenance on the furnace, AC, and water heater. Furnace is operational at departure.

….

Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and flame sensor circuitry. • Checked venting system for proper draft, secure connections, and obstruction-free flue path. • Tested carbon monoxide levels at the supply, return, and flue to ensure safe operation. Burner & Combustion System • Cleaned burner assembly and verified prope

Waiting on excelsior to get back with me about the HX price and time

dampers

Estimate

Installed wire to provide power to the humidifier

Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and Completed a comprehensive furnace tune-up to ensure safe, efficient, and reliable operation for the home. Work performed included: System Inspection & Safety Checks • Inspected heat exchanger for cracks, corrosion, and proper flame pattern. • Verified operation of all safety controls, including high-limit switch, rollout switch, pressure switch, and flame sensor circuitry. • Checked venting system for proper draft, secure connections, and obstruction-free flue path. • Tested carbon monoxide levels at the supply, return, and flue to ensure safe operation. Burner & Combustion System • Cleaned burner assembly and verified prope

Arrived for furnace check on two systems. On the upstairs system everything was running in manufacturing specs. I did change filters. The solenoid valve for the humidifier has failed. With approval I replaced it and humidifier is working properly. On the downstairs system everything is running on manufacturing specs. I replaced filter here too. I could not get humidifier to run. We will schedule another visit to get it going. Systems are running at departure . Thanks for choosing LBA.