Kansas City, KS HVAC & Plumbing Services

…

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Checked systems heat exchanger to ensure proper venting of flue gas. Performed an electronic gas leak search. Verified operation of the humidifier. Furnace and humidifier are operational at this time.

Today I did a full heating maintenance on 6 RTU units I changed all filters took amp draws from inducer and blower motor all systems are running and working perfectly at this time.

*(*)*)*)*;&)&))&)&)&)&**)**))*)*)*)*)*)*))* Materials: Three triple A batteries used from the dollar store 3 filters that were not changed (dated 3/25) ***(*((((((****(((((((**** Today all three rooftop units were electrically and mechanically checked for function. The east unit that serves the restroom had a clogged burner orifice that was cleared and the batteries in the thermostat were dead and replaced today. The middle unit is not cooling properly due to a degraded and packed evaporator coil and possible low charge. The west unit that serves the break-room is heating properly however it has a failed compressor that had been removed from service. All heating functions are back in service for all three units and they are safe to operate. I do recommend capacitor replacements and a control board replacement. Estimates were created and emailed for these repairs. Cooling repairs and/or replacement estimates were declined at this time due to winter’s soon arrival. Thank you,

today I did a maintenance on 1 RTU until changed all filters took amp draws checked heat exchanger everything looks good at this time.

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Found that the system is operating with excessive static pressure. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the fan is collecting dust. Checked systems heat exchanger to ensure proper venting of flue gas. Performed an electronic gas leak search. Cleaned up the systems installation(drain and loose wires). Furnace is operational at this time.

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Checked systems heat exchanger to ensure proper venting of flue gas. Performed an electronic gas leak search. Furnace is operational at this time.

Dispatched for a heating tune-up. During the inspection of the heating system each component is checked to confirm it is within manufacturer specifications. The components that are checked include heat strips, temperature split, blower amps, heat pump change over to aux heat, heat pump components and cleanness of blower wheel. After reviewing all components of the system, it is operating within manufacturer specifications. Thank you for allowing us in your house to provide the perfect home service and look forward to you becoming a member of the Perfect Family Service Club from your LBA Lead Service Tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

Supply line loose on shut off

First floor unit had a clogged condensation line. I cut open the cooper drain line and flushed the line clear of all blockage. I put a fernco for access in the future. At this time the unit is draining as it should be

Will return with access panel. Do job all at once

Arrived to do a performance maintenance. Set up for combustion analysis temperature split and static pressure tests. Found that the system is operating with failing static pressure. Verified operation of all mechanical and electronic components of the furnace. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the bearings for the fan are making excessive noise. Checked systems heat exchanger to ensure proper venting of flue gas. Found debris that has fallen off the evaporator coil. Performed an electronic gas leak search. Furnace is operational at this time.

10/10/25 - Completed a full heating maintenance on three RTU’s. The filters were changed, the heat exchangers were checked, and proper operation was tested. Overall, all three units were in good condition, they were all running well, and there were no issues found at this time.

*((()*)*)()*)***()*)**)*)*)*)* 2hrs labor used. Unsure if it was a flat rate or hourly or I would have added the 2hrs *)*)*))&)&)&)&))&)&)&)&)&*)*))*)*)*))*)*)*))*)*) During maintenance and heating checks I discovered that the indoor blower assembly was very dirty. Today the blower motor assembly was removed from the furnace. The wheel, motor and assembly was cleaned then reinstalled. The system was operated on heat, cool and fan only modes to confirm that the reinstallation was successful. The system was left on heat mode and set to 55deg. Thank you, Jon Tech notes: Carrier M/N 58DLA045 - - - 10108 S/N 0604A25840;

Replaced faucet

Dispatched for furnace tune-up. The components that are tested during the tuneup are heat exchanger, flame sensor, igniter, blower wheel, inducer, temp split and combustion in the heat exchanger. All components of the furnace are with in range of manufacture specifications. Thank you for allowing us in your house to provide the perfect home service and for being a member of the perfect family service club from your LBA Lead Service tech Calvin. If I provided a positive or five star experience. I’d appreciate you sharing your thoughts in a review.

The 2 barred units are good passed full heating maintenance. The three RTU are not working in cooling or heating and will need a service call will need to return.

***(*((**(***)&()&(&)&)&)&)&))&)& Installed a new t-stat and filter *)*)*;*))*)*)*)*)*)*)*))*)*)*)*)*)*)*)*))*) Today there a hanging unit heater, a split-system (A/C+gas heat) and a hot water heater were checked for function and safety. The electrical and mechanical systems were checked and the units were operated. Amp draws were gathered and the bearings were checked in all motors. During this visit I was asked to replace the thermostat and install a filter in the split system. The thermostat and filter were sourced and installed today. All equipment checked today passed with the exception of the furnace blower compartment. I recommend removing the blower assembly, cleaning it and reinstalling due to the amount of dust that has accumulated. This was relayed to Brad and he will be addressing it. Forms were filled out for each system and emailed to Blake. There is a one year parts and labor warranty on the new thermostat. Thank you, Jon

Customer supplied

10/8/25 - Completed a full heating maintenance on one furnace. The filter was changed and proper operation was tested. Overall, the furnace was running well, it was in good condition, and there were no issues found at this time.

Arrived for furnace check today. Static pressure is passing. Heat exchanger looks good. Carbon monoxide test was 0ppm. There is a 40 degree temp rise. All electrical components are running within specs. We changed filter today too. System is operating properly. Thanks for choosing LBA.

During fall maintenance the N.E hanging unit heater was found to have a capacitor that was leaking. The capacitor was replaced with a new and tested capacitor. This repair is covered under a one year warranty from today’s date. The unit returned to normal function after the repair was completed. Thank you, Jon

- split system defrosting due to dirty filter. Will return and replace filter and then check temps

-

Today I diagnosed that the second stage compressor that’s as rewired to operate as the first stage compressor has failed with a winding short to ground. The contactor that serves this compressor has also failed and is fused closed. This was the only operating compressor left to provide cooling. The blower wheel in this unit was also making a screaming noise when operating. Upon request from the client the compressor and blower motor were removed from operation. This unit is twinned with the unit next to it towards the west. I confirmed that the unit to the west returned to A/C mode when completed. Information was gathered and forwarded to provide options to move forward with replacement or repair (if feasible). Thank you Jon Tech notes: York S/n N1E1055733 Compressor shorted to ground Contactor fused Blower wheel grinding Above was disabled as per client